The Stockport Resin Driveway Company

Resin bound driveways in Stockport maintenance guide.

Resin bound driveways in Stockport maintenance guide

Photo of a brush head that has been used to sweep a resin bound driveway surface in Stockport

​Resin driveways are a long-lasting, low-maintenance surface solution that provides many advantages. Some of these are adaptability in terms of both design and construction, durability, and simplicity of care. Having a low maintenance requirement is not the same as having no requirement at all. However, thanks to its low maintenance requirements, resin bound driveways in Stockport are a popular choice amongst clients. This blog post will show your clients how to maintain their resin so that it lasts as long as possible.

Best practices for working with resin bound driveways

Resin surfaces are only safe for light foot or vehicle traffic and should not be subjected to heavy or unusual use. When it is feasible, safeguards should be put in place to prevent unexpected damage. Unless specifically designed for, resin bound surfacing should not be used for parking or frequent traffic by heavy freight vehicles.

What NOT to do

Parking cars and other typical driveway applications won’t be a problem for your resin bound driveway. But you should still take care to avoid the following activities, which could cause damage:

Heavy skips

If you have a resin bound driveway, you should not put heavy skips with sharp edges straight on the driveway. Load-bearing planks can be utilised for smaller skips, but it’s best to find another spot if at all possible.

Motorbike stands

It’s best to keep the hefty motorcycle’s stand, for example, off the surface.

Avoid heavy dragging

Never drag anything heavy across your resin bound driveway.

Spill hazards

Solvents can soften and harm the resin binder, thus they should be avoided at all costs.

Chemical exposure caution

In terms of chemical resistance, resin-bound surfaces iare among the best options available. For the first week after installation, avoid exposing the surface to chemicals so that it can develop its full chemical resistance.

Car tyres

Tire markings can be avoided by not twisting the steering wheel while the vehicle is parked. Rubber does not come off the tyre to the surface, but rather, the oils already present on the surface are heated by the friction of the tyres or by the residual heat left over from a lengthy trip.

Maintenance cleaning

Stockport resin bound driveways can be kept in good condition with regular sweepings with a stiff brush, which can remove debris and prevent a variety of problems. This will eliminate moss growth by removing leaves and other debris. Furthermore, foreign objects, stains, and other potential damage can be washed away with a good old-fashioned hosing down.

Maintenance-free jet washing

Infrequent cleaning with a pressure washer or sweeper equipped with water jetting and vacuuming equipment is required. However, the proper technique for jet washing a resin bound surface should be known. So here are the easy steps to jet washing your driveway.

Step 1

If a flat nozzle is available, we suggest using it to ensure an even coat throughout the flat surface.

Step 2

Make use of a jet wash/pressure washer with a pressure of up to 150 bar. Keep in mind that too much pressure could crack your surface.

Step 3

The water temperature should be refreshingly chilly but not freezing. The resin can be protected from heat damage by keeping the temperature moderate.

Step 4

Keep the spray nozzle at least 20cm from the surface you’re spraying. Too close of an approach with a high-pressure jet wash can cause surface damage.

Step 5

A “sweeping” action in which you spray back and forth is recommended.

Step 6

To get rid of the finer particles that a broom can miss, we advise jet cleaning your resin driveway after sweeping.

Some of the most common cleaning problems for resin bound driveways

Cleansing a driveway of moss and algae

The surface should be prepared by treating any weed growth that may have occurred previous to surfacing, as fresh weed growth is exceedingly unlikely to be maintained. To eliminate and prevent regrowth, use a specific moss and algae killer, such as “algon,” and apply it periodically as directed by the manufacturer. Then a powerful bleach solution can be used to eliminate embedded algae growth and restore the surface’s original colour. Use this following the manufacturer’s instructions and any applicable regional regulations. But remember, it’s important to thoroughly cleanse the area with clean water after application.

Fixing a resin driveway in Stockport that has become overgrown with weeds

A resin bonded surface is built to resist weed growth as part of its design. While every effort should be made, weeds can nonetheless appear on occasion (as on any surface). As a rule, this is because of seeds being blown around by the wind. But the good news is that you can safely pull a few weeds by hand without ruining the surface. Yet, when pulling weeds by hand, the entire root must be removed rather than just the tops. For some weeds, mowing them down only encourages further growth. So it is recommended to use an effective pesticide or weed killer to eliminate the weeds if they have established deep roots. Domestic weed killers can be used to treat small, weed-seeded areas without damaging the surface. Keep in mind that tanning might leave stains if surfaces aren’t regularly wiped down for fallen leaves, twigs, seeds, and the like.

Cleaning gum off a resin bound driveway

Gum chewing can be a major problem. Once it sets, it can be tough to get rid of and it’s not very attractive to look at. Try spraying the gum with a freezing spray and then carefully scraping it off with a wall scraper if you are unable to remove it by sweeping or jet cleaning. But don’t risk surface damage by trying to remove the gum with a harsh edge.

How to remove oil stains from resin bound driveways

If you have a resin bound driveway, oil and grease can cause ugly stains. Always use extreme caution to prevent the accidental release of oil and greasy compounds. Rapidly mopping up and flushing away any leaks is essential. Rainfall has the potential to clean up oil spills, although this doesn’t always happen. Warm water (that we don’t see much in Stockport) and a moderate household detergent can also be used to remove oil or grease. After letting this soak in for 10 minutes, a jet wash should be performed.

How to sort concrete or cement stains on a resin bound driveway

Careful application of diluted hydrochloric acid or a specific cement remover, followed by a thorough rinse with clean water, can get rid of cement or concrete stains. But it’s important to remember that the acid will also dissolve the lime-based aggregate if you use it. So it is best to call on your local resin bound driveway installers to take care of this.

The treatment for mineral stains

The resin bound surface is constructed from organic, dried aggregates. Despite our best efforts, trace amounts of iron pyrites may occur in the environment. In the event of staining, the readily accessible oxalic acid can be used to effectively remove the blemishes from the affected area. Then after employing the specialised acid solution, it must be removed with cold water.

Clearing snow from a resin driveway in winter

Snow and ice may damage any driveway surface in the winter. It is impossible to avoid frost and snow unless the surface is sheltered. Thankfully, it’s not hard to get over this weather problem. A regular snow shovel can be used to remove snow from resin bound driveways in Stockport without causing the aggregates to fly everywhere. Loose gravel driveways are prone to this problem because the pebbles might become entangled with the snow. However, the use of a metal shovel is discouraged since it could cause surface damage if not handled with care. Then once most of the snow is removed, the moisture from the remains can be absorbed into the earth below. This is another advantage of a permeable resin-bonded surface as it helps prevent icy patches.

Removing frost and ice buildup on top of a driveway

Ice and frost can be removed with the help of salt applied to the surface. But after the weather has returned to normal, the salt/grit must be rinsed off thoroughly to get rid of any remaining salt.

Restoring a resin bound area

Localised damage to the surface can be fixed. The broken spot needs to be chiselled away. Then, the same aggregate mixture can be combined with DALTEX UVR Resin and laid down. The edges of the repair should be “feathered” to blend in with the surrounding area for a sturdy, flawless, and long-lasting result.

Additional suggestions for a more durable resin driveway

  • Wooden boards should be used to evenly distribute the weight of any large loads before being placed on your resin bound driveway.
  • Clean up any accidents right away as faster action will make them simpler to clear.
  • Avoid dropping or dragging anything sharp or hard, such as motorbike supports, big plant pots, gardening gear, etc.

Conclusion

We think we have probably covered the most common resin bound driveway surface problems in this blog post. However, do you have a unique issue that you would like professional advice on? Then simply Google “resin bound near me” and as we’re a local company and great at what we do you should find us at the top of the search results. Now you can call us directly and we can either work out your dilemma over the phone or arrange a site visit.

Leave a Comment

Your email address will not be published. Required fields are marked *